ECUHELP HT-PROG Full Version With Dongle Stand-alone Device Support on Bench / Boot / BDM ECU Programmer / ECU Clone Tool etc

Highlights:

1. ECUHELP HTprog includes MPC Module, EEPROM module, BDM adapter, Tricore adapter, Dongle 
2. Works online with an internet connection every time
3. No need to connect with ECUHELP KT200

Notice:
1. It is advised to uninstall any antivirus software and disable the firewall before using the ECUHELP HTprog.
2. It is important not to upgrade the software to avoid any potential damage to the hardware. Can't support update.
3. Activation of the HTprog is necessary and should be done using the user's registered email address.
4. Install software version: 1.0.45, Free Download HTProg Software 

ECUHELP HTprog Feature

HTprog is the latest programming equipment for the automotive electronics industry.
Can do chip tuning,DTC removal, adblue removal EGR cancellation, DPF cancellation, hot start, speed limit release, IMMO off , etc . and make ECU-related operations by reading and writing ECU.
Can also read and write car body modules, such as CAS, SZL, FRM, AIRBAG, EZS, BCM, etc. With this function, you can easily deal with matching keys, unlocking anti-theft, adjusting instruments and repairing airbag computers, etc.
For the repair, calibration and replacement of automotive electronic modules, it can even refresh the key, so that the old key can be a new key and continue to match other vehicles.

ECUHELP HTprog support list:
HTprog ECU Clone Function List
HTprog on Bench Programmer Function List

HTprog Functions: 

Chip Tuning / ECU Cloning
With HTprog you can read and write P-Flash,D-Flash, External Flash and external EEPROM with the option of automatically checksum correction, you will have many methods in most of ECUS :
1. Factory mode (On Bench for most of ECU/TCU): with this option you don't have to open the ECU cover. Just plug some wires for power and signals and you are ready to go. 
2.Tricore Boot Mode for all Tricore ECU: Opening the ECU is mandatory to connect the boot wire on the ECU board.This method is useful when the ECU is not responding
3.BDM (Background debug mode) 
4.JTAG for Renesas and Freescale

BDM Read / Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW. EIZ / EIS in Mercedes Benz. BCM in Volkswagen and Porsche.etc.

Built in Editors
With HTprog you can edit many Flash data like: 
Edit CAS3+ VIN, ISN and keys 
Edit CAS4,CAS4+ VIN,and ISN
Edit mileage for BMW instrument clusters

Other functions
You can do key reset for many brands like Audi, BMW,MIN, Porsche, Toyota,Fiat, Renault...etc.
Read/Write a wide range of SOP8 EEPROMS.
Works side by side with Autohex to make keys.

Key Features
Master version. One License for all protocols on bench.
Supports one of the largest ECU/TCU list in Cars and Trucks for ECU cloning and Chip Tuning. Supports both old and latest ECU / TCUs from Bosch,Continental, Delphi, Marelli,Denso, Tenic,TRW and Valeo.etc.
Reads all BMW long ISN from BMW DME and DDE including MD1 and MG in F/G series

IMMO BDM Read/Write
With HTprog you are able to break the protection of immobilizers like CAS in BMW, EIZ / EIS in Mercedes Benz.BCM in Volkswagen and Porsche...etc.

Package Includes:

 

1pc x HT-PROG adapter

1pc x MPC module

1pc x EEprom module

1pc x 12V adapter

1pc x BDM cable

1pc x TriCore cable

1pc x USB cable
1pc x Softdog